Invictus Wireless - Wireless Solutions for 802.11abgn, WiFi, Antennas, etc.

The RMS-200 is a unique remote monitoring, data acquisition and control device specifically designed for use with battery powered wireless internet repeater sites and other AC/DC powered remote equipment. Powered by DC voltage from 10 to 60 volts, the RMS-200 offers ultra low power consumption and uses the LINUX operating system for versatility, stability and security. It uses embedded Ethernet technology for internet data acquisition and remote voltage & temperature monitoring. Among its many features, USB and Serial ports offer additional peripheral functions such as webcams and the relays offer a wide variety of normally off/on combinations for remote device control.

The RMS-200 offers you the secure situational awareness you need to keep equipment operational and conditions monitored in a cost effective and compact design.

Contact us for help with your project 503-635-2562, info@invictusnetworks.com

Model: RMS-200 RMS-100 The baby RMS - Is a unique remote monitoring, data acquisition, and control device specifically designed for use with battery powered wireless repeater sites or other AC & DC powered remote equipment projects.

Has ultra low power consumption and won't put a drain on your power source. Uses only 1.2 watts and is powered by DC voltage from 10 to 60 volts. Uses embedded Ethernet technology for internet data acquisition and remote voltage monitoring and the LINUX operating system for versatility, stability, and security. Gives you the situational awareness you need to keep your equipment operational and reliable.

Model: RMS-100 The TPW Series Wind Turbines from Tycon Power Systems are lightweight at less than 10.5kg and are designed for ease of installation and long service life. The generator is a very low cogging force design for better performance in light winds and is packaged in a fully sealed die cast anodized aluminum enclosure. There are no brushes to wear out or cause electrical noise and the bearings are sealed so the system is maintenance free. The blades are glass reinforced polypropylene for high strength, UV resistance and fatigue resistance. The 200W & 400W turbines are available in a 12V or 24v model.

The permanent magnets used are Neodymium Iron Boron (NdFeB) for higher power output.

Mounting is to the top of a 51mm (2inch) OD standard pole. The mount system is a vibration isolation type to minimize vibrations being carried down the mounting pole. The hardware used is stainless steel for corrosion protection.

Now includes a battery charging controller to prevent battery over-charge and over-discharge. Controller supports a dump load if desired but connecting a dump load is not a requirement with this system. Controller can be used in conjunction with a solar controller to create a hybrid power system

Model TPW-400-12

400 Watt, 24 Volt, 10amp, HAWT type, Wind Turbine with Controller by Tycon Power Systems

200 Watt, 24 Volt, 6 Amp, HAWT type, Wind Turbine with Controller by Tycon Power Systems

200 Watt,12 Volt, 12Amp, HAWT type, Wind Turbine with Controller by Tycon Power Systems

In stock soon. Order now to get in line. First come first served
List Price: $599.95
Our Price: $549.00
Sale Price: $539.00
You save $60.95!

In stock soon. Order now to get in line. First come first served
List Price: $519.95
Our Price: $489.95
Sale Price: $479.00
You save $40.95!

Usually ships in 24~48 hours
List Price: $519.95
Our Price: $489.95
Sale Price: $479.00
You save $40.95!

The TPW Series Wind Turbines from Tycon Power Systems are lightweight at less than 10.5kg and are designed for ease of installation and long service life. The generator is a very low cogging force design for better performance in light winds and is packaged in a fully sealed die cast anodized aluminum enclosure. There are no brushes to wear out or cause electrical noise and the bearings are sealed so the system is maintenance free. The blades are glass reinforced polypropylene for high strength, UV resistance and fatigue resistance. The 200W & 400W turbines are available in 12V or 24v versions.

The permanent magnets used are Neodymium Iron Boron (NdFeB) for higher power output.

Mounting is to the top of a 51mm (2inch) OD standard pole. The mount system is a vibration isolation type to minimize vibrations being carried down the mounting pole. The hardware used is stainless steel for corrosion protection.

Now includes a battery charging controller to prevent battery over-charge and over-discharge. Controller supports a dump load if desired but connecting a dump load is not a requirement with this system. Controller can be used in conjunction with a solar controller to create a hybrid power system

Model TPW-400-24 The TPW Series Wind Turbines from Tycon Power Systems are lightweight at less than 10.5kg and are designed for ease of installation and long service life. The generator is a very low cogging force design for better performance in light winds and is packaged in a fully sealed die cast anodized aluminum enclosure. There are no brushes to wear out or cause electrical noise and the bearings are sealed so the system is maintenance free. The blades are glass reinforced polypropylene for high strength, UV resistance and fatigue resistance. The 200W & 400W turbines are available in a 12V or 24v versions.

The permanent magnets used are Neodymium Iron Boron (NdFeB) for higher power output. Mounting is to the top of a 51mm (2inch) OD standard pole. The mount system is a vibration isolation type to minimize vibrations being carried down the mounting pole. The hardware used is stainless steel for corrosion protection.

Now includes a battery charging controller to prevent battery over-charge and over-discharge. Controller supports a dump load if desired but connecting a dump load is not a requirement with this system. Controller can be used in conjunction with a solar controller to create a hybrid power system

Model TPW-200-24 (also available in 12vDC version - see TPW-200-12) The TPW Series Wind Turbines from Tycon Power Systems are lightweight at less than 10.5kg and are designed for ease of installation and long service life. The generator is a very low cogging force design for better performance in light winds and is packaged in a fully sealed die cast anodized aluminum enclosure. There are no brushes to wear out or cause electrical noise and the bearings are sealed so the system is maintenance free. The blades are glass reinforced polypropylene for high strength, UV resistance and fatigue resistance. The 200W & 400W turbines are available in a 12V or 24v versions.

The permanent magnets used are Neodymium Iron Boron (NdFeB) for higher power output. Mounting is to the top of a 51mm (2inch) OD standard pole. The mount system is a vibration isolation type to minimize vibrations being carried down the mounting pole. The hardware used is stainless steel for corrosion protection.

Now includes a battery charging controller to prevent battery over-charge and over-discharge. Controller supports a dump load if desired but connecting a dump load is not a requirement with this system. Controller can be used in conjunction with a solar controller to create a hybrid power system

Model TPW-200-12 (also available in 24vDC version - see TPW-200-24)

SLAB-2419 802.11g Hi-Power Radio with Integrated 19dBi Antenna by Teletronics

IN STOCK - PowerBridge M5 Carrier Class 5GHz Wireless Bridge (sold as each end of link) by Ubiquiti

IN STOCK - RocketM5-GPS, 802.11N MIMO 2.4 Ghz Rocket AP from Ubiquiti

IN STOCK NOW
Our Price: $295.00
Sale Price: $275.00
You save $20.00!

IN STOCK NOW
Our Price: $269.00
Sale Price: $259.95
You save $9.05!

IN STOCK NOW
Our Price: $239.95
Sale Price: $219.95
You save $20.00!

Teletronics SLAB 2419 High Power 250mW 802.11bg WiFi Access Point / Client Bridge with Integrated 19dBi Flat Panel Antenna and heavy duty cast adjustable mast mounting hardware.

With an integrated 19dBi patch antenna, this all-in-one TT™2400 with integrated 19dBi includes the following:

Use two for point-to-point bridge over multiple miles
250mW 802.11b/g WiFi, AP or Bridge/Client mode
Adjustable Mast Mounting Hardware
Power-over-Ethernet (PoE) Injector
120vAC Power Supply

For additional details, click on the link above, on features tab or contact us by email or phone.

Model 11-157 SLAB 2419 150+Mbps of real outdoor throughput and up to 20km+ range. PowerBridge M products utilize Ubiquiti's revolutionary AirMax™ TDMA protocol enabling scalable, carrier-class PtP or PtMP network performance. Additionally, AirControl™ application allows operators to centrally manage 100's of devices. Super-Efficient 25dBi Dual-Polarity Array Panel Design provides optimum MIMO performance at long distances. PowerBridge packs revolutionary performance in a compact and weatherproof design.

Robust, Efficient Mechanical Design

Advanced Antenna Technology

Breakthrough Wireless Performance, AirMax & AirControl Support

Model PBM5 PowerBridgeM5 - (Required for Complete Point to Point Bridge Link) Many situations require the use of multiple AirMax M series devices on the same tower. The new Rocket M GPS products are designed to eliminate co-location interference by using synchronized transmission times. With AirSync, the basestations make use of a common clock source using the built-in GPS receiver. One device is configured as the synchronization master and the others are configured in Slave Mode. Once this is done, the Master and Slave devices synchronize their transmit and receive cycles so that they transmit at the same time and receive at the same time.
The Rocket M GPS products are rugged, hi-power, linear 2x2 MIMO radios with enhanced receiver performance. They feature incredible range performance (50+km) and breakthrough speed (150+Mbps real TCPI/IP). They are specifically designed for outdoor PtP bridging and PTMP AirMax basestation applications.

Model: RocketM5-GPS, RM5-GPS, Rocket M5-GPS

Join our mailing list